CRS-1升级过程

network

CRS-1升级过程

前两天弄了台CRS-1，由于也是首次接触，也是非常担心不能出错。俗话说，怕什么来什么，果不其然，插上一块十G的线卡后，无法识别（给大家注明一下，机箱型号为CRS-4，1-Port 10-Gigabit Ethernet SPA[SPA-1X10GE-WL-V2]，8-Port Gigabit Ethernet single SPA，软件版本为3。4），后来一查思科的文档，发现3。4不支持啊，没办法。升级吧。下软件（网通机房真够快，1.8m/s），里面还附带着一个升级说明的PDF。讲了一大通，不过重点可能就是后半部分。
按照说明，把软件安装成功了，也就是这一步：router(admin)# install add <source>/<path>/<pie> sync
可是这一步却出错了：router(admin)# install activate disk0:comp-hfr-mini-3.6.0 sync
错误信息如下：the installation will fail with the following error:
Error: Cannot proceed with the activation because of the following
Error: package incompatibilities:
Error: hfr-fpd-3.4.1 needs hfr-os-mbi-3.4.1, or equivalent, to be
Error: active on the same nodes.
Error: hfr-fpd-3.4.1.CSCsi86270-1.0.0 needs
Error: hfr-base-3.4.1.CSCsi86270-1.0.0, or equivalent, to be active on
Error: the same nodes)

后来才知道，要把原来的安装包deactive。然后 install remove 后才行。这是后话，当时不知道啊。没办法尝试其它方法吧

下载的软件中包括一个comp-hfr-mini.vm-3.6.0，这可是个好东西。TFTP，拷到disk0下（或者直接从TFTP引导也行。要有TFTP就要在ROMMON下设置那些参数了。我嫌麻烦就没弄。）然后ctrl+c(这个和原来的系统不太一样，得等到
MBI validation sending request.
HIT CTRL-C to abort 时按才管用),
rommon>boot disk0:/comp-hfr-mini.vm-3.6.0
然后你就慢慢等吧。大约得一个小时吧。就装好了。果然10G的小卡认出来了。不过还得升级PIE包。反正都升一下吧，又得半个多小时。装完之后，别忘了这一步：
router(admin)# install  commit
然后还有这步：
router(admin)# upgrade hw-module fpd all location all



========================================================================
硬件配置如下:

Product Number and Description		Qty

CRS-4/S      Cisco CRS-1 Series 4 Slots Carrier Routing System		1
CRS-4-AC-KIT       CRS-1 4 Slot System AC Kit		1
CAB-CRS4AC-AU       CRS-1 4 Slot AC Power Cord (Australia)		4
CRS-8-RP       Cisco CRS-1 Series 8 Slots Route Processor		2
XC-RPK9-03.04       Cisco IOS XR IP/MPLS Core Software 3DES		2
CRS1-SIP-800       Cisco Carrier Routing System SPA Interface Processor Card		1
SPA-1X10GE-WL-V2       Cisco 1-Port 10GE WAN/LAN-PHY Shared Port Adapter		2
SPA-8X1GE       8-port Gigabit Ethernet Shared Port Adapter		1
XFP-10GZR-OC192LR       10GBASE-ZR and OC192 LR2 XFP Module		2
CRS-MSC-40G       Cisco CRS-1 Series Modular Services Card 40G		1
CRS1-SIP-800       Cisco Carrier Routing System SPA Interface Processor Card		1
SPA-1X10GE-WL-V2       Cisco 1-Port 10GE WAN/LAN-PHY Shared Port Adapter		2
SPA-8X1GE       8-port Gigabit Ethernet Shared Port Adapter		1
XFP-10GZR-OC192LR       10GBASE-ZR and OC192 LR2 XFP Module		2
CRS-MSC-40G       Cisco CRS-1 Series Modular Services Card 40G		1
Included: CRS-4-AC-SHELF       Cisco CRS-1 Series AC Power Shelf for CRS-4		1
Included: CRS-4-AC-SUPPLY       Cisco CRS-1 Series AC Supply for CRS-4		4
Included: GLC-LH-SM       GE SFP, LC connector LX/LH transceiver		4
Included: CRS-MSC       Cisco CRS-1 Series Modular Services Card		1
Included: XC-LC40G       Cisco CRS-1 Series MSC 40G license		1
Included: CRS-MSC       Cisco CRS-1 Series Modular Services Card		1
Included: XC-LC40G       Cisco CRS-1 Series MSC 40G license		1
Included: CRS-4-CH       Cisco CRS-1 Series 4 Slots Chassis		1
Included: CRS-4-FAN-TR       Cisco CRS-1 Series Fan Tray for CRS-4		1
Included: CRS-4-FC       Cisco CRS-1 Series Fabric Card for CRS-4		4
Included: CRS-4-FC-BLANK       Cisco CRS-1 blank impedence cover for CRS-1/4 fabric card		4
Included: CRS-8-RP-BLANK       Cisco CRS-1 Series 8 Slot Route Processor Blank		2
Included: CRS-INT-IMPEDANCE       Cisco CRS-1 Series impedence cover for Interface slot		4
Included: CRS-MSC-IMPEDANCE       Cisco CRS-1 Series Impedence cover for MSC Slot		4

拓扑呢,给大家大体说一下吧,四个大城市,具体就不说了,四台CRS互连,中间是DWDM.

配置如下还没完全配置完成)

RP/0/RP0/CPU0:CRS#show run
Building configuration...
!! Last configuration change at Sun Jan 20 13:47:52 2008 by cisco
!
hostname CRS
line default
password 7 youguess
!
telnet vrf default ipv4 server max-servers 5
cdp
interface Loopback0
ipv4 address X.Y.100.21 255.255.255.255
!
interface MgmtEth0/RP0/CPU0/0
ipv4 address X.Y.Z.1 255.255.255.0
!
interface MgmtEth0/RP1/CPU0/0
shutdown
!
interface GigabitEthernet0/0/2/0
shutdown
!
interface GigabitEthernet0/0/2/1
shutdown
!
interface GigabitEthernet0/0/2/2
shutdown
!
interface GigabitEthernet0/0/2/3
shutdown
!
interface GigabitEthernet0/0/2/4
shutdown
!
interface GigabitEthernet0/0/2/5
shutdown
!
interface GigabitEthernet0/0/2/6
shutdown
!
interface GigabitEthernet0/0/2/7
shutdown
!
interface GigabitEthernet0/2/1/0
description connect CRS->6000
ipv4 address X.Y.1.1 255.255.255.252
!
interface GigabitEthernet0/2/1/1
shutdown
!
interface GigabitEthernet0/2/1/2
shutdown
!
interface GigabitEthernet0/2/1/3
shutdown
!
interface GigabitEthernet0/2/1/4
shutdown
!
interface GigabitEthernet0/2/1/5
shutdown
!
interface GigabitEthernet0/2/1/6
shutdown
!
interface GigabitEthernet0/2/1/7
shutdown
!
interface TenGigE0/0/0/0
shutdown
!
interface TenGigE0/0/3/0
shutdown
!
interface TenGigE0/2/0/0
shutdown
!
interface TenGigE0/2/3/0
mtu 9180
ipv4 address X.Y.1.6 255.255.255.252
!
controller wanphy0/0/0/0
lanmode on
!
controller wanphy0/0/3/0
lanmode on
!
controller wanphy0/2/0/0
lanmode on
!
controller wanphy0/2/3/0
lanmode on
!
router static
address-family ipv4 unicast
  0.0.0.0/0 X.Y.X.Z
!
!
end
RP/0/RP0/CPU0:CRS#





然后就好了。另外说明一下的是：两个RP最好一块一块的升级。